1Department of Chemical Engineering, University of Technology, Baghdad, Iraq
2Training Center, Baghdad, Iraq
BibTex Citation Data :
@article{BCREC15367, author = {Marwah Al-Nuaim and Asawer A. Al-Wasiti and Zainb Y. Shnain and Abbas K. Al-Shalal}, title = {The Combined Effect of Bubble and Photo Catalysis Technology in BTEX Removal from Produced Water}, journal = {Bulletin of Chemical Reaction Engineering & Catalysis}, volume = {17}, number = {3}, year = {2022}, keywords = {Photocatalytic process; air bubbles; coating; varnish; TiO2; BTEX}, abstract = { Among the several ways used in wastewater treatment, the photocatalysis process is a more novel and alternative process that is increasingly employed in recent years. This work aims to improve the performance of the photocatalyst process by using air bubbles in removing the BTEX from produced water as an indicator of process efficiency. The study also shows the effect of influencing factors (pH and residence time) on the photocatalysis process. The study was done in a rectangular column with dimensions of 200 mm width, 30 mm depth, and 1500 mm height. Commercial titanium oxide (TiO 2 ) coated on a plate by the varnish was used as a source of the photocatalyst. The experiment was carried out under different values of gas flow rate (0-3 L/min) to evaluate its effect on the photocatalyst process, the effect of other variables of pH (3-11), and irradiation time (30-120) min was also studied. A new method of the coating was adopted by using an alumina plate with varnish as an adhesive. The characteristics results show that the coated plate has hydrophilic properties and that there is no significant change in the crystal structure of the TiO 2 nanoparticles and the varnish before and after 60 h of the photocatalytic process, indicating that the plate is still effective after 60 h usage under different conditions. The results also show that the introduction of air bubbles enhances the removal efficiency of BTEX significantly and the best removal effectiveness of BTEX was 93% when pH = 5 after 90 min and 90% when pH = 3 after 120 min. The removal rate also reached 86% when pH = 7 after 120 min all at a flow rate of 3 L/min. The percentage of removal decreased at pH = 9 and 11, reaching 64% and 50%, respectively after 120 min and a flow rate of 3 L/min. Copyright © 2022 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License ( https://creativecommons.org/licenses/by-sa/4.0 ). }, issn = {1978-2993}, pages = {577--589} doi = {10.9767/bcrec.17.3.15367.577-589}, url = {https://journal.bcrec.id/index.php/bcrec/article/view/15367} }
Refworks Citation Data :
Among the several ways used in wastewater treatment, the photocatalysis process is a more novel and alternative process that is increasingly employed in recent years. This work aims to improve the performance of the photocatalyst process by using air bubbles in removing the BTEX from produced water as an indicator of process efficiency. The study also shows the effect of influencing factors (pH and residence time) on the photocatalysis process. The study was done in a rectangular column with dimensions of 200 mm width, 30 mm depth, and 1500 mm height. Commercial titanium oxide (TiO2) coated on a plate by the varnish was used as a source of the photocatalyst. The experiment was carried out under different values of gas flow rate (0-3 L/min) to evaluate its effect on the photocatalyst process, the effect of other variables of pH (3-11), and irradiation time (30-120) min was also studied. A new method of the coating was adopted by using an alumina plate with varnish as an adhesive. The characteristics results show that the coated plate has hydrophilic properties and that there is no significant change in the crystal structure of the TiO2 nanoparticles and the varnish before and after 60 h of the photocatalytic process, indicating that the plate is still effective after 60 h usage under different conditions. The results also show that the introduction of air bubbles enhances the removal efficiency of BTEX significantly and the best removal effectiveness of BTEX was 93% when pH = 5 after 90 min and 90% when pH = 3 after 120 min. The removal rate also reached 86% when pH = 7 after 120 min all at a flow rate of 3 L/min. The percentage of removal decreased at pH = 9 and 11, reaching 64% and 50%, respectively after 120 min and a flow rate of 3 L/min. Copyright © 2022 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0).
Article Metrics:
Last update:
In order for Masyarakat Katalis Indonesia - Indonesian Catalyst Society (MKICS) and BCREC Publishing Group to publish and disseminate research articles, we need non-exclusive publishing rights (transfered from author(s) to publisher). This is determined by a publishing agreement between the Author(s) and Masyarakat Katalis Indonesia - Indonesian Catalyst Society (MKICS) and BCREC Publishing Group. This agreement deals with the transfer or license of the right for publishing to Masyarakat Katalis Indonesia - Indonesian Catalyst Society (MKICS) and BCREC Publishing Group, while Authors still retain significant all copy rights to use and share their own published articles. Masyarakat Katalis Indonesia - Indonesian Catalyst Society (MKICS) and BCREC Publishing Group supports the need for authors to share, disseminate and maximize the impact of their research and these rights, in any databases.
As a journal Author, you have all copy rights for a large range of uses of your article, including use by your employing institute or company. These Author copy rights can be exercised without the need to obtain specific permission. Authors who publishing in BCREC journals have wide copy rights to use their works for teaching and scholarly purposes without needing to seek permission, including, but not limited to:
Authors/Readers/Third Parties can copy and redistribute the material in any medium or format, as well as remix, transform, and build upon the material for any purpose, even commercially, but they must give appropriate credit (the name of the creator and attribution parties (authors detail information), a copyright notice, an open access license notice, a disclaimer notice, and a link to the material), provide a link to the license, and indicate if changes were made (Publisher indicates the modification of the material (if any) and retain an indication of previous modifications using a CrossMark Policy and information about Erratum-Corrigendum notification).
Authors/Readers/Third Parties can read, print and download, redistribute or republish the article (e.g. display in a repository), translate the article, download for text and data mining purposes, reuse portions or extracts from the article in other works, sell or re-use for commercial purposes, remix, transform, or build upon the material, they must distribute their contributions under the same license as the original Creative Commons Attribution-ShareAlike (CC BY-SA).
The Authors submitting a manuscript do so on the understanding that if accepted for publication, non-exclusive right for publishing (publishing right) of the article shall be assigned/transferred to Publisher of Bulletin of Chemical Reaction Engineering & Catalysis journal (Masyarakat Katalis Indonesia - Indonesian Catalyst Society (MKICS) and BCREC Publishing Group).
Upon acceptance of an article, authors will be asked to complete a 'Right Transfer Agreement for Publishing (RTAP)'. An e-mail will be sent to the Corresponding Author confirming receipt of the manuscript together with a 'Right Transfer Agreement for Publishing' form by online version of this agreement.
Bulletin of Chemical Reaction Engineering & Catalysis journal and Masyarakat Katalis Indonesia-Indonesian Catalyst Society (MKICS), the Editors and the Advisory International Editorial Board make every effort to ensure that no wrong or misleading data, opinions or statements be published in the journal. In any way, the contents of the articles and advertisements published in the Bulletin of Chemical Reaction Engineering & Catalysis are sole and exclusive responsibility of their respective authors and advertisers.
Remember, even though we ask for a transfer of right for publishing (RTAP), our journal Author(s) still retain (or are granted back) significant scholarly copy rights as mentioned before.
The Right Transfer Agreement for Publishing (RTAP) Form can be downloaded here: [Right Transfer Agreement for Publishing (RTAP) Form BCREC 2025]
The copyright form should be signed electronically and send to the Editorial Office in the form of original e-mail below: Prof. Dr. I. Istadi (Editor-in-Chief)Editorial Office of Bulletin of Chemical Reaction Engineering & CatalysisLaboratory of Plasma-Catalysis (R3.5), UPT Laboratorium Terpadu, Universitas DiponegoroJl. Prof. Soedarto, Semarang, Central Java, Indonesia 50275Telp/Whatsapp: +62-81-316426342E-mail: bcrec[at]live.undip.ac.id ; bcrec[at]che.undip.ac.id
(This policy statements has been updated at 24th January 2024)