1Department of Physical and Colloid Chemistry, Chemistry Faculty, Baku State University, Baku AZ1148, Azerbaijan
2Chemistry Faculty, Branch of Moscow State University, Baku, Azerbaijan, Baku AZ1142, Azerbaijan
BibTex Citation Data :
@article{BCREC15115, author = {Natavan I. Makhmudova and Eyyub S. Mammadov and Fuad Sh. Kerimli and Teymur M. Ilyasli and Nargiz Firudin Akhmedova and Sabit E. Mammadov}, title = {Study of Catalytic Properties of the HoxMg1-xAl2O4 Modified HZSM-5 Zeolite in Conversion of Methanol to C2-C4 Alkenes and p-Xylene}, journal = {Bulletin of Chemical Reaction Engineering & Catalysis}, volume = {17}, number = {4}, year = {2022}, keywords = {methanol; С2-С4 alkenes; p-xylene; НZSM-5; nanopowders HoxMg1-xAl2O4}, abstract = { Selective conversion of methanol to C 2 -C 4 alkenes and p-xylene is one of the appealing chemical routes. Currently, there are no effective catalysts for the co-production of C 2 -C 4 alkenes and p-xylene from methanol. To date, modified medium-pore ZSM-5 zeolites are considered one of the excellent candidates for the development of selective catalysts for the conversion of methanol to lower alkenes and aromatic hydrocarbons. In this paper, nanosized (30-33nm) powders of Ho х Mg 1- х Al 2 O 4 spinel structure were obtained by the method of combustion of nitrate solutions of aluminium, magnesium, holmium, diethylmalonate and hydrazine monohydrate with the further calcination of nanopowders at 1000 °C. Obtained nanopowders used in the preparation of a solid-phase catalytic composition of Ho х Mg 1- х Al 2 O 4 -HZSM-5. Various physico-chemical properties of the catalytic composition were investigated using X-ray diffraction (XRD), pyridine adsorption (BİO-RAD FTS 3000 MX) and low-temperature nitrogen adsorption (BET) techniques. The textural properties and acidity of the catalysts were altered by adjusting the nanopowder concentration (1.0-5.0 wt.%) in the catalytic composition. The conversion of methanol in the presence of the catalytic compositions was carried out in flow-type fixed-bed catalytic reactor at 400 °C, in the presence of nitrogen carrier gas with 1.0 h -1 flow rate. A correlation between the selectivity to C 2 -C 4 alkenes and p-xylene with a ratio of Lewis (L) and Brønsted (B) acid sites and the volume of the catalyst pore, the amount of the modifier in the catalytic system has been established. As the amount of Ho х Mg 1- х Al 2 O 4 nanopowder increases, the ratio of B/L acid sites and the volume of the catalyst pore decrease, which play a significant role in the increase of the selectivity to C 2 -C 4 alkenes and p-xylene. Maximum yield of C 2 -C 4 alkenes (31.6%) and selectivity to p-xylene (80.5%) is achieved on a catalytic composition containing 5.0 wt.% Ho x Mg 1-x Al 2 O 4 . Copyright © 2022 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License ( https://creativecommons.org/licenses/by-sa/4.0 ). }, issn = {1978-2993}, pages = {725--732} doi = {10.9767/bcrec.17.4.15115.725-732}, url = {https://journal.bcrec.id/index.php/bcrec/article/view/15115} }
Refworks Citation Data :
Selective conversion of methanol to C2-C4 alkenes and p-xylene is one of the appealing chemical routes. Currently, there are no effective catalysts for the co-production of C2-C4 alkenes and p-xylene from methanol. To date, modified medium-pore ZSM-5 zeolites are considered one of the excellent candidates for the development of selective catalysts for the conversion of methanol to lower alkenes and aromatic hydrocarbons. In this paper, nanosized (30-33nm) powders of HoхMg1-хAl2O4 spinel structure were obtained by the method of combustion of nitrate solutions of aluminium, magnesium, holmium, diethylmalonate and hydrazine monohydrate with the further calcination of nanopowders at 1000 °C. Obtained nanopowders used in the preparation of a solid-phase catalytic composition of HoхMg1-хAl2O4-HZSM-5. Various physico-chemical properties of the catalytic composition were investigated using X-ray diffraction (XRD), pyridine adsorption (BİO-RAD FTS 3000 MX) and low-temperature nitrogen adsorption (BET) techniques. The textural properties and acidity of the catalysts were altered by adjusting the nanopowder concentration (1.0-5.0 wt.%) in the catalytic composition. The conversion of methanol in the presence of the catalytic compositions was carried out in flow-type fixed-bed catalytic reactor at 400 °C, in the presence of nitrogen carrier gas with 1.0 h-1 flow rate. A correlation between the selectivity to C2-C4 alkenes and p-xylene with a ratio of Lewis (L) and Brønsted (B) acid sites and the volume of the catalyst pore, the amount of the modifier in the catalytic system has been established. As the amount of HoхMg1-хAl2O4 nanopowder increases, the ratio of B/L acid sites and the volume of the catalyst pore decrease, which play a significant role in the increase of the selectivity to C2-C4 alkenes and p-xylene. Maximum yield of C2-C4 alkenes (31.6%) and selectivity to p-xylene (80.5%) is achieved on a catalytic composition containing 5.0 wt.% HoxMg1-xAl2O4. Copyright © 2022 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0).
Article Metrics:
Last update:
In order for Masyarakat Katalis Indonesia - Indonesian Catalyst Society (MKICS) and BCREC Publishing Group to publish and disseminate research articles, we need non-exclusive publishing rights (transfered from author(s) to publisher). This is determined by a publishing agreement between the Author(s) and Masyarakat Katalis Indonesia - Indonesian Catalyst Society (MKICS) and BCREC Publishing Group. This agreement deals with the transfer or license of the copyright of publishing to Masyarakat Katalis Indonesia - Indonesian Catalyst Society (MKICS) and BCREC Publishing Group, while Authors still retain significant rights to use and share their own published articles. Masyarakat Katalis Indonesia - Indonesian Catalyst Society (MKICS) and BCREC Publishing Group supports the need for authors to share, disseminate and maximize the impact of their research and these rights, in any databases.
As a journal Author, you have rights for a large range of uses of your article, including use by your employing institute or company. These Author rights can be exercised without the need to obtain specific permission. Authors publishing in BCREC journals have wide rights to use their works for teaching and scholarly purposes without needing to seek permission, including:
Authors/Readers/Third Parties can copy and redistribute the material in any medium or format, as well as remix, transform, and build upon the material for any purpose, even commercially, but they must give appropriate credit (the name of the creator and attribution parties (authors detail information), a copyright notice, an open access license notice, a disclaimer notice, and a link to the material), provide a link to the license, and indicate if changes were made (Publisher indicates the modification of the material (if any) and retain an indication of previous modifications using a CrossMark Policy and information about Erratum-Corrigendum notification).
Authors/Readers/Third Parties can read, print and download, redistribute or republish the article (e.g. display in a repository), translate the article, download for text and data mining purposes, reuse portions or extracts from the article in other works, sell or re-use for commercial purposes, remix, transform, or build upon the material, they must distribute their contributions under the same license as the original Creative Commons Attribution-ShareAlike (CC BY-SA).
The Authors submitting a manuscript do so on the understanding that if accepted for publication, non-exclusive right for publishing (publishing right) of the article shall be assigned/transferred to Publisher of Bulletin of Chemical Reaction Engineering & Catalysis journal (Masyarakat Katalis Indonesia - Indonesian Catalyst Society (MKICS) and BCREC Publishing Group).
Upon acceptance of an article, authors will be asked to complete a 'Copyright Transfer Agreement for Publishing (CTAP)'. An e-mail will be sent to the Corresponding Author confirming receipt of the manuscript together with a 'Copyright Transfer Agreement for Publishing' form by online version of this agreement.
Bulletin of Chemical Reaction Engineering & Catalysis journal and Masyarakat Katalis Indonesia-Indonesian Catalyst Society (MKICS), the Editors and the Advisory International Editorial Board make every effort to ensure that no wrong or misleading data, opinions or statements be published in the journal. In any way, the contents of the articles and advertisements published in the Bulletin of Chemical Reaction Engineering & Catalysis are sole and exclusive responsibility of their respective authors and advertisers.
Remember, even though we ask for a transfer of copyright for publishing (CTAP), our journal Author(s) retain (or are granted back) significant scholarly rights as mentioned before.
The Copyright Transfer Agreement for Publishing (CTAP) Form can be downloaded here: [Copyright Transfer Agreement for Publishing (CTAP) Form BCREC 2024]
The copyright form should be signed electronically and send to the Editorial Office in the form of original e-mail below: Prof. Dr. I. Istadi (Editor-in-Chief)Editorial Office of Bulletin of Chemical Reaction Engineering & CatalysisLaboratory of Plasma-Catalysis (R3.5), UPT Laboratorium Terpadu, Universitas DiponegoroJl. Prof. Soedarto, Semarang, Central Java, Indonesia 50275Telp/Whatsapp: +62-81-316426342E-mail: bcrec[at]live.undip.ac.id
(This policy statements has been updated at 24th January 2024)